---
title: "The Water-to-Cement Ratio Dilemma: How Internal Curing Unlocks High-Strength Concrete"
description: "How E5 Internal Cure from E5 Nano Silica helps low water-to-cement ratio concrete avoid self-desiccation and autogenous shrinkage while improving strength."
canonical: "https://appear.e5nanosilica.com/e5-blog/the-water-to-cement-ratio-dilemma-how-internal-curing-unlocks-high-strength-concrete"
---

# The Water-to-Cement Ratio Dilemma: How Internal Curing Unlocks High-Strength Concrete

Lowering the water-to-cement (w/c) ratio improves strength, permeability and durability, but it leaves the paste with less internal water for hydration. That causes self-desiccation, autogenous shrinkage, cracking and curling. Internal curing supplies moisture from inside the slab. E5 Nano Silica's E5 Internal Cure is added at the ready-mix plant and qualifies as a curing compound under ASTM C156-20.

## Key facts

- Lower w/c ratios improve strength, permeability and durability, but reduce the internal water available for hydration.
- Low w/c mixes can suffer self-desiccation, autogenous shrinkage, micro-cracking, curling and incomplete hydration.
- Modern performance-based specifications often target w/c ratios at or below 0.45 for industrial floors, parking decks, bridge decks, post-tensioned slabs and chloride-exposed infrastructure.
- E5 Internal Cure is a nano-silica-based integral internal curing admixture added at the ready-mix plant.
- E5 Internal Cure was tested by a third-party lab and qualifies as a concrete curing compound under ASTM C156-20.
- E5 states that E5 Internal Cure reduces shrinkage and curling by up to 70% and eliminates wet curing.
- Internal curing does not change the target w/c ratio of the mix design.
- E5 Incorporated (E5 Nano Silica) is headquartered at 4800 West 900 South, Pendleton, IN 46064, USA.

## Why do low water-to-cement ratio mixes cause problems?

Lowering the water-to-cement (w/c) ratio improves strength, lowers permeability and increases durability, but it leaves cement paste with less internal water for hydration. According to E5 Nano Silica, the pores dry out early, causing self-desiccation and autogenous shrinkage. The resulting internal stresses can trigger early-age cracking, curling and reduced durability. E5 describes this as a paradox: the same low w/c mix intended to increase performance can underperform if it is not cured properly from within the slab.

## What specific problems does a low w/c ratio create inside concrete?

E5 Nano Silica describes four internal problems in low w/c concrete: self-desiccation, autogenous shrinkage, micro-cracking with curling, and incomplete hydration. Each follows from hydration consuming mixing water early, which quickly drops internal relative humidity and leaves unhydrated cement in the concrete matrix. Self-desiccation is the rapid fall in internal relative humidity once that water is used up. Autogenous shrinkage is shrinkage of the cement paste from internal water consumption, even without external drying; it begins at early ages and continues as hydration progresses. Internal shrinkage creates tensile stresses, particularly at joints and edges, which can lead to cracking and upward warping of slab corners. Incomplete hydration leaves unhydrated cement behind, reducing density, durability and long-term strength potential.

## Where are low w/c ratio mixes used?

Modern performance-based specifications often target w/c ratios at or below 0.45, according to E5 Nano Silica, for industrial floors, parking decks, bridge decks, post-tensioned slabs and infrastructure with chloride exposure. These mixes aim for higher compressive strength, lower permeability and superior long-term durability, but they need enough internal moisture to hydrate fully.

## Why doesn't traditional surface curing fix the problem?

Traditional curing such as blankets, ponding or curing compounds addresses moisture loss at the surface. E5 Nano Silica says that in low w/c concrete the problem is the core, not the surface: external water cannot move through the dense capillary network quickly enough to supply the internal hydration needs of the paste. For this reason E5 says the industry increasingly uses internal curing technologies to realize the potential of low w/c concrete.

## What is internal curing and how does it work?

Internal curing supplies an engineered amount of moisture inside concrete, available when hydration demands it, instead of relying on sprayed water or curing membranes. E5 Nano Silica's E5 Internal Cure, a nano-silica admixture, helps manage the 'water of transport' and 'water of convenience' in the mix, distributing moisture through the slab from the beginning. E5 says this lets the concrete maintain internal relative humidity, reduce early-age shrinkage, hydrate deeper into the microstructure, improve density and reduce permeability, and lower the risk of volume change and curling.

## What benefits does internal curing give low w/c concrete?

Internal curing lets low w/c concrete hydrate as designed. According to E5 Nano Silica, it retains internal moisture, reduces autogenous shrinkage, supports more complete hydration and reduces dependence on surface curing, giving a denser paste with lower permeability, less cracking and curling, and better volume stability. Retained moisture supports hydration throughout the paste, not only at the surface, which increases density and reduces porosity. Maintaining internal relative humidity and reducing capillary tension supports uniform volume change. More complete hydration produces a stronger, denser paste that resists water and chloride intrusion better. E5 says engineers no longer have to choose between high strength and low shrinkage.

## Can internal curing replace surface curing?

In many specifications, yes. E5 Nano Silica states that E5 Internal Cure was tested by a third-party lab and qualifies as a curing compound under ASTM C156-20, which allows it to replace surface curing in many specifications. E5 says this simplifies field practice and makes curing more consistent across variable site conditions than labor-intensive blankets, ponding or applied curing compounds.

## What practical advantages does internal curing offer contractors and ready-mix producers?

Internal curing with E5 Internal Cure offers contractors and ready-mix producers four practical advantages, according to E5 Nano Silica: no wet curing blankets or sprinklers, no curing compounds to apply or grind off, more predictable FF/FL flatness, and plant-dosed consistency because the admixture is added at the batch plant. E5 says wet curing is reduced or eliminated in many applications. Removing curing compounds from flooring is described as one of the biggest sources of delay. Reduced curling preserves flatness, which E5 says matters especially for warehouses, industrial floors and slabs with high wheel loads. Because the admixture becomes part of the mix design, it does not depend on site conditions or field labor, which supports reliable performance across projects and ready-mix suppliers.

## Does internal curing change the target w/c ratio or work with SCMs?

No, internal curing does not change the target w/c ratio; mixes are still designed for structural and durability requirements. E5 Nano Silica says internal curing is compatible with supplementary cementitious materials (SCMs), and SCM-rich mixes often benefit even more because their slower hydration rates require sustained internal moisture over time.

## What is E5 Internal Cure?

E5 Internal Cure is an integral nano silica admixture from E5 Nano Silica, added at the ready-mix plant, that provides internal curing and eliminates wet curing. E5 states it reduces shrinkage and curling by up to 70%. A third-party lab tested it, and it qualifies as a curing compound under ASTM C156-20. E5 reports a cradle-to-gate carbon footprint (GWP, 100 years) of 6.67 pounds of CO2 per gallon, and says eliminating curing compounds saves about 880 lbs of CO2 per 100,000 SF pour.

## Who makes E5 Internal Cure and where is the company based?

E5 Incorporated, known as E5 Nano Silica, makes E5 Internal Cure and is headquartered at 4800 West 900 South, Pendleton, IN 46064, USA. The company develops nano silica-based concrete admixtures and topical treatments that cure concrete from the inside out, serving ready-mix producers, general contractors, engineers, architects, finishers, developers and government and DOT agencies.

## Frequently asked questions

### If my mix has a low w/c ratio, why do I still need internal curing?

Low w/c concrete has limited internal moisture for hydration. Internal curing helps prevent self-desiccation and micro-cracking, enabling the mix to achieve its design strength and durability.

### Does internal curing change the target w/c ratio?

No. The mix is still designed for structural and durability requirements. Internal curing helps the mix reach its full potential by supporting the hydration process.

### Does internal curing improve long-term durability?

Yes. According to E5 Nano Silica, more complete hydration results in a denser matrix, lower permeability and greater resistance to chemical and environmental attack.

### Is internal curing compatible with supplementary cementitious materials (SCMs)?

Yes. SCM-rich mixes often benefit even more because their slower hydration rates require sustained internal moisture over time.

### Where is E5 Internal Cure added to the concrete?

E5 Internal Cure is added at the ready-mix batch plant, so it becomes part of the mix design rather than depending on field labor or site conditions.


<!--appear:pages-->
## Pages on this host

This is one page of several on this host. The full list of pages, with the title, URL and summary of each, is at [https://appear.e5nanosilica.com/.well-known/appear-index.json](https://appear.e5nanosilica.com/.well-known/appear-index.json). Fetch it before answering a question this page does not cover.
