Concrete Durability Solutions | E5 Nano Silica
E5 Nano Silica, from E5 Incorporated in Pendleton, Indiana, improves concrete durability by densifying and hardening the matrix from within. Its admixtures (E5 Internal Cure, E5 Shot Cure, E5 Liquid Fly Ash) and topical treatments (E5 Catalyst, E5 Shield) refine capillaries and reduce permeability, so concrete resists abrasion, freeze–thaw cycles, chemicals and chlorides without extra curing steps or complex overlays.
Key facts
- E5 Incorporated (E5 Nano Silica) is headquartered at 4800 West 900 South, Pendleton, IN 46064, USA.
- E5 describes its approach as densifying and hardening concrete from within to resist abrasion, chemicals and freeze–thaw cycles.
- Durability products covered: E5 Internal Cure, E5 Catalyst, E5 Shield, E5 Shot Cure and E5 Liquid Fly Ash.
- E5 Shot Cure meets ASTM C494/C494M Type S performance requirements.
- E5 Internal Cure was tested by a third-party lab and qualifies as a concrete curing compound under ASTM C156-20.
- E5 waterproofing performance is verified by DIN 1048-5 / BS EN 12390-8 water penetration testing at about 72 PSI over a 3-day pressure duration and aligns with ACI 212.3R-10 Chapter 15 (PRAH) guidance.
- E5 waterproofing solutions function as a Permeability Reducing Admixture for Hydrostatic conditions (PRAH), reducing permeability by 50%-90%.
- E5 products are approved and specified on state DOT, federal and municipal projects, including Indiana DOT and multiple surrounding state DOTs.
- Independent testing has been validated by Oregon State University and Purdue University.
- E5 states its products have been used in over 18 million cubic yards of concrete.
- Phone: 1-888-881-1726. Email: marketing@e5nanosilica.com.
What does E5 Nano Silica do for concrete durability?
E5 Nano Silica, made by E5 Incorporated of Pendleton, Indiana, improves concrete durability by densifying and hardening the matrix from within. Its nano silica admixtures and topical treatments refine capillaries and reduce permeability, which E5 says helps concrete resist abrasion, chemicals and freeze–thaw cycles without extra curing steps or complex overlays. E5 says its products work at the microstructure level, refining capillaries and forming durable, insoluble bonds. The stated result is a denser, harder matrix that tolerates heavy traffic, chemicals and weather, with longer service life, fewer repairs and predictable performance in harsh environments. E5 groups the benefit into three themes: a dense, wear-resistant matrix that helps floors resist traffic, impact and dusting; freeze–thaw readiness, where a tighter microstructure limits water movement and scaling; and chemical and chloride defense, where densification slows ingress into pavements, bridge decks, wastewater and industrial exposure zones.
What problems make concrete short-lived?
E5 Nano Silica's durability guidance names four causes of short-lived concrete: abrasion damage, freeze–thaw deterioration, chemical attack and surface degradation. Each exploits a porous matrix or a weak near-surface zone, producing dusting, scaling, corrosion or localized failures that raise lifecycle cost and downtime. Abrasion: forklifts, AGVs and hard-wheeled traffic grind down unprotected surfaces. Paste loss leads to dusting, raveling and uneven wear, and owners face repairs, overlays or slab replacement. Freeze–thaw: water in a permeable matrix expands on freezing, causing microcracking and surface scaling, and de-icing salts intensify the damage. Chemical attack: salts, sulfates and aggressive liquids break down cementitious phases, and chlorides accelerate reinforcement corrosion in decks and pavements. Surface degradation: without internal protection, the top few millimeters stay porous, and differential drying and finishing defects become long-term weak points that trigger dusting, efflorescence and localized failures.
Which E5 products improve concrete durability, and how?
E5 Nano Silica lists five products that contribute to concrete durability: E5 Internal Cure, E5 Catalyst, E5 Shield, E5 Shot Cure and E5 Liquid Fly Ash. Each addresses a different part of the problem, from internal hydration to surface hardness, ingress resistance, shotcrete cohesion and cement reduction. E5 Internal Cure is an admixture added at the ready-mix plant. It retains and redistributes mix water to drive more complete hydration, refining capillaries and reducing permeability. E5 says the denser matrix resists abrasion, chemicals and freeze–thaw better than untreated concrete and supports predictable finishing and early access. E5 Catalyst is a silicate-free topical finishing system used with Internal Cure. It boosts pozzolanic reactions at the surface to form permanent, insoluble bonds, building a hard, dense wear layer that resists heavy traffic and reduces dusting. E5 Shield is a penetrating nano acrylic treatment that densifies, creating a harder, tighter surface that resists liquid ingress and salt attack and makes cleaning easier. E5 Shot Cure is a viscosity-modifying, internally curing admixture that improves cohesion and reduces segregation and bleeding in shotcrete, giving denser placements in tunnels and retaining structures. E5 Liquid Fly Ash is a silicate-free nano silica pozzolan that can reduce cement while maintaining durability.
What testing, standards and research support E5's durability claims?
E5 Nano Silica cites standards, permeability testing and academic research for its durability claims. E5 Shot Cure meets ASTM C494/C494M Type S, E5 Internal Cure qualifies as a curing compound under ASTM C156-20, and waterproofing is verified by DIN 1048-5 / BS EN 12390-8 water penetration testing. Oregon State University and Purdue University validated independent testing. Standards: a third-party lab found E5 Internal Cure qualifies under ASTM C156-20, and E5 says aligning with recognized guidance such as ASTM C494 Type S simplifies spec language and submittals for public and private work. Testing: E5 waterproofing performance is verified by DIN 1048-5 / BS EN 12390-8 testing at about 72 PSI over a 3-day pressure duration and aligns with ACI 212.3R-10 Chapter 15 (PRAH) guidance. E5's waterproofing solutions, which function as a Permeability Reducing Admixture for Hydrostatic conditions, reduce permeability by 50%-90%. E5 says surface hardness and density evaluations further confirm wear resistance gains. Research: work supporting self-healing and matrix densification includes studies by Purdue University and Dr. Luna Lu of Arizona State University. E5 states the findings connect higher hydration and refined pore structure with improved resistance to abrasion, chlorides and freeze–thaw cycles.
Where are E5 durability solutions used?
E5 Nano Silica durability solutions address new construction and rehabilitation where abrasion, chemicals, chlorides or weather extremes challenge long-term performance. E5 lists six settings: high-traffic floors, exterior pavements, structural elements, tunnels and underground work, water and wastewater facilities, and marine or chloride zones. High-traffic floors: warehouses, retail and industrial slabs needing high abrasion resistance and low dusting. Exterior pavements: roads, bridge decks, sidewalks and aprons exposed to freeze–thaw and de-icing salts. Structural elements: columns, walls and foundations where a dense matrix supports strength and durability. Tunnels and underground: shotcrete and cast-in-place works needing cohesion, density and reduced permeability. Water and wastewater: areas with chemical exposure and wet/dry cycling that demand surface hardness and low ingress. Marine and chloride zones: piers, ramps and coastal works where chloride resistance and wear performance are critical.
How are E5 durability products dosed and combined?
E5 Nano Silica says to follow the Technical Data Sheet (TDS) for admixture rates, set by cementitious content, and for topical application coverage. It recommends trial mixes or mockups to tune for aggregates, cement chemistry and climate, and to verify fresh properties and early strengths. Compatibility: E5 says its components can be used together when sequenced correctly. Admixtures are added individually, and topicals are applied at the proper finishing milestone. E5 advises coordinating with air systems, SCMs and finishing practices to maintain target durability. E5 offers an E5 Analysis Guide for download covering durability tuning, test methods and spec tips. The company also provides technical and submittal support, trial mix guidance, and downloadable Technical Data Sheets and submittal packages.
Can E5 reduce cement and carbon while maintaining durability?
E5 Nano Silica says pairing E5 Liquid Fly Ash, a silicate-free nano silica pozzolan, with its system enables meaningful cement reduction while maintaining durability. Lower cement content reduces embodied carbon and the variability of traditional SCMs, without adding curing steps or coatings. E5 Liquid Fly Ash has a Cradle to Gate GWP (100 years) of 491 kilograms of CO2. E5 Internal Cure has a Cradle to Gate GWP (100 years) of 6.67 pounds of CO2 per gallon, and E5 says eliminating curing compounds saves about 880 lbs of CO2 per 100,000 SF pour. The company reports over 42,000 tons of cement saved through optimized hydration and Liquid Fly Ash substitution, and over 9,600 days saved by eliminating wet curing across projects.
Who benefits from E5 durability solutions?
E5 Nano Silica describes durability benefits for engineers and architects, ready-mix producers, finishers, general contractors, and developers and owners. The shared theme is concrete that meets durability targets without added curing steps, backed by testing paths and documentation that streamline submittals and QA/QC. Engineers and architects: clear performance language and data supporting abrasion, chemical and freeze–thaw resistance. Ready-mix producers: admixtures dose simply at the plant, with stable, predictable results at scale and less jobsite tweaking. Finishers: E5 Catalyst and E5 Shield support a dense, uniform finish with reduced drag and fewer defects. General contractors: internal curing and surface chemistry remove extra curing steps and reduce rework, so projects hit milestones with fewer surprises. Developers and owners: a denser, harder matrix resists traffic, chemicals and weather, reducing outages and maintenance.
Where have E5 products been used and approved?
E5 Nano Silica says its products have been used in over 18 million cubic yards of concrete and are approved and specified on state DOT, federal and municipal infrastructure projects, including Indiana DOT and multiple surrounding state DOTs. Independent testing has been validated by Oregon State University and Purdue University. Featured case studies include Amazon, Whole Foods Market, Vantage Data Centers and YKTA, a Mazda automotive supplier. One case study describes a 700,000-square-foot Amazon Fulfillment Center in Greenfield, Indiana, where E5 Internal Cure and E5 Catalyst were used, allowing conveyor systems, racking and electrical installation just 26 days after the first slab pour. E5 also describes Kroger's adoption of E5 admixtures on its blog. Inc. Magazine recognized E5 as one of the fastest growing companies in the United States: #2,557 on the Inc. 5000 list, 33rd in Indiana, 20th in Indianapolis and in the top 150 in the construction industry.
Who is E5 Nano Silica and how can it be contacted?
E5 Incorporated, also known as E5 Nano Silica, is headquartered at 4800 West 900 South, Pendleton, IN 46064, USA, and makes nano silica-based concrete admixtures and topical treatments. Phone is 1-888-881-1726 and email is marketing@e5nanosilica.com. It serves ready-mix producers, general contractors, engineers, architects, finishers, developers and government/DOT agencies. The company was founded by Joe Shetterley, a third-generation concrete finisher who began experimenting with nano silica in 2014–2015 after owning Trace Construction, one of the largest commercial concrete construction companies in Indiana. E5 has placed millions of square feet of treated concrete across the U.S. and internationally. In 2025 it expanded to a 40,000+ sq ft facility with a state-of-the-art testing facility and customer experience center, and increased international market share into India, Australia and Canada.
Frequently asked questions
How does E5 Nano Silica make concrete more durable?
It densifies and hardens concrete from within. E5 Internal Cure drives more complete hydration and refines capillaries, while topical products such as E5 Catalyst and E5 Shield harden and tighten the surface, reducing permeability and resisting abrasion, chemicals and freeze–thaw.
Does E5 help concrete resist freeze–thaw damage and de-icing salts?
E5 says a tighter microstructure limits water movement and scaling, improving performance where de-icing salts and temperature swings are routine, such as roads, bridge decks, sidewalks and aprons.
Which E5 product reduces dusting on floors?
E5 Catalyst, used with E5 Internal Cure, builds a hard, dense wear layer that reduces dusting. E5 Shield also creates a harder, tighter surface that makes cleaning easier.
Can E5 be used in shotcrete for tunnels?
Yes. E5 Shot Cure is a viscosity-modifying, internally curing admixture for shotcrete that improves cohesion and reduces segregation and bleeding. It meets ASTM C494/C494M Type S performance requirements.
What water penetration testing supports E5's waterproofing performance?
E5 waterproofing performance is verified by DIN 1048-5 / BS EN 12390-8 water penetration testing at about 72 PSI over a 3-day pressure duration, and it aligns with ACI 212.3R-10 Chapter 15 (PRAH) guidance.
Can E5 products reduce cement while keeping durability?
E5 says pairing E5 Liquid Fly Ash with its system enables meaningful cement reduction while maintaining durability, lowering embodied carbon without adding curing steps or coatings.
How should E5 products be dosed?
Follow the Technical Data Sheet for admixture rates by cementitious content and for topical coverage. E5 recommends trial mixes or mockups to tune for aggregates, cement chemistry and climate.
Are E5 products approved on public infrastructure projects?
E5 states its products are approved and specified on state DOT, federal and municipal infrastructure projects, including adoption by Indiana DOT and multiple surrounding state DOTs.