E5 Nano Silica Moisture Mitigation Solutions for Concrete Slabs
E5 Nano Silica, made by E5 Incorporated of Pendleton, Indiana, mitigates concrete slab moisture as a system. E5 Internal Cure manages water from within new concrete. E5 Catalyst, E5 Miracle Aid and E5 Shield densify and condition the surface. The aim is stable relative humidity, controlled pH and adhesive-safe slabs without last-minute epoxy mitigation.
Key facts
- E5 Incorporated, maker of E5 Nano Silica, is headquartered at 4800 West 900 South, Pendleton, IN 46064, USA
- E5 moisture mitigation is a system: internal curing (E5 Internal Cure) plus surface treatments (E5 Catalyst, E5 Miracle Aid, E5 Shield)
- E5 Internal Cure is an integral admixture added at the ready-mix plant and reduces shrinkage and curling by up to 70%
- E5 Internal Cure was tested by a third-party lab and qualifies as a concrete curing compound under ASTM C156-20
- E5 Catalyst is a topical, silicate-free finishing system used with E5 Internal Cure that controls moisture and pH for flooring adhesion
- E5 Miracle Aid is a nano silica topical finishing aid that increases surface workability without altering the water-to-cement ratio
- E5 Shield is a penetrating, moisture-blocking nano acrylic treatment for existing concrete that reduces porosity and MVER, positioned as an alternative to epoxy moisture mitigation
- E5 waterproofing solutions function as a Permeability Reducing Admixture for Hydrostatic conditions (PRAH) and reduce permeability by 50%-90%
- Independent testing of E5 products has been validated by Oregon State University and Purdue University
- A featured case study describes a 700,000-square-foot Amazon Fulfillment Center in Greenfield, IN, where E5 Internal Cure and Catalyst allowed conveyor, racking and electrical installation 26 days after the first slab pour
How does E5 Nano Silica mitigate moisture in concrete slabs?
E5 Nano Silica, from E5 Incorporated in Pendleton, Indiana, mitigates slab moisture with a system rather than a single product. E5 Internal Cure manages water from within new concrete, while the surface treatments E5 Catalyst, E5 Miracle Aid and E5 Shield densify and condition the slab. The aim is stable relative humidity, controlled pH and adhesive-safe substrates. E5 describes this as addressing moisture at its source in the concrete matrix, not just on the surface.
How do you prevent flooring adhesive failure on a new concrete slab?
To prevent flooring adhesive failure on a new slab, E5 Nano Silica recommends managing moisture during placement and finishing rather than after the fact. That means E5 Internal Cure in the mix, surface treatments such as E5 Catalyst and E5 Miracle Aid during finishing, then in-slab RH testing, pH checks and bond tests before flooring goes down. E5 also advises coordinating RH and pH limits with adhesive and flooring manufacturers.
What causes high surface pH and bond failure under flooring?
According to E5 Nano Silica, bonds weaken and coverings detach when high relative humidity and elevated pH reach the adhesive line. Moisture also drives efflorescence and softens the surface paste, compounding defects. E5 Catalyst is the product E5 uses to condition surface pH, working with E5 Internal Cure to slow moisture movement. E5's material does not explain the chemical source of the elevated pH.
What problems does uncontrolled moisture cause under flooring?
According to E5 Nano Silica, uncontrolled slab moisture causes four problems: delamination and adhesive failure, mold and mildew concerns, project delays and added steps, and elevated risk and lifecycle cost. These can mean callbacks, patching, space closures and replacement costs for owners. E5 says damp, porous slabs can sustain microbial growth under impervious finishes, and that waiting for slabs to dry out and then adding coatings or epoxy mitigation puts extra time and trades on the critical path. Ignoring moisture at placement can lead to premature flooring replacement and repeat mitigation events.
How does E5 Internal Cure help prevent moisture problems in new concrete?
E5 Internal Cure, an integral admixture from E5 Nano Silica added at the ready-mix plant, controls evaporation in fresh concrete to increase cement hydration and reduce capillary continuity. The matrix becomes denser and less moisture-mobile under non-hydrostatic conditions, which E5 says supports earlier, more predictable floor-covering readiness. A third-party lab tested it, and it qualifies as a concrete curing compound under ASTM C156-20. E5 also states it eliminates wet curing and reduces shrinkage and curling by up to 70%.
How does E5 Catalyst control moisture migration and surface pH?
E5 Catalyst is a topical, silicate-free finishing system from E5 Nano Silica, used with E5 Internal Cure. It creates a hard, dense, abrasion-resistant wear layer while conditioning surface pH and controlling moisture for flooring adhesion. E5 says it slows moisture movement and tunes surface chemistry, supporting adhesive performance and reducing under-floor issues. A downloadable Technical Data Sheet is available for E5 Catalyst.
How does E5 Miracle Aid reduce water vapor transmission?
E5 Miracle Aid is a nano silica topical finishing aid from E5 Nano Silica that increases surface workability without changing the water-to-cement ratio. E5 says it produces a less permeable, denser surface during finishing, helping lower water vapor transmission at the flooring interface, and that it stabilizes the finishing window to reduce defects that become moisture pathways. It also reduces drag during troweling.
How can a slab be ready for flooring without an epoxy mitigation coating?
E5 Nano Silica positions E5 Shield, a penetrating, moisture-blocking nano acrylic treatment for existing concrete, as an alternative to epoxy moisture mitigation in many retrofit scenarios. It reduces porosity and moisture vapor emission rate (MVER) by densifying the substrate rather than coating over it. For new slabs, E5 combines Internal Cure with surface treatments to avoid last-minute epoxy mitigation. Suitability for a specific slab should be confirmed with E5 and the flooring manufacturer.
What is a moisture vapor reduction admixture and how is it specified?
E5 Nano Silica's material does not define 'moisture vapor reduction admixture' as a formal term. It describes specification as following each product's Technical Data Sheet: Internal Cure dosed per cementitious content, and topical application rates for Catalyst, Miracle Aid and Shield. E5 also advises trial mixes and field mockups, and coordinating RH and pH limits with flooring manufacturers. E5 offers downloadable Technical Data Sheets and submittal packages, and an Analysis Guide with RH/pH checks, spec tips and workflows.
Can E5 moisture mitigation products be used together?
Yes. E5 Nano Silica states that its moisture-mitigation components can be used together when sequenced correctly: admixtures are added individually, and topical products are applied at finishing milestones. E5 advises following each product's Technical Data Sheet, running trial mixes and field mockups to suit local materials, climate and floor-covering requirements, and coordinating with adhesive and flooring manufacturers to maintain warranty pathways.
What testing and standards back E5 moisture mitigation?
E5 Nano Silica says its moisture-mitigation components are validated for moisture migration control, surface hardness and density, and pH conditioning. E5 Internal Cure qualifies as a curing compound under ASTM C156-20 after third-party lab testing. Independent testing of E5 products has been validated by Oregon State University and Purdue University. Field verification commonly includes in-slab RH testing, pH checks and bond tests before flooring is installed.
What research supports E5's moisture and durability claims?
Research supporting E5 Nano Silica's self-healing and matrix densification claims includes work by Purdue University and Dr. Luna Lu of Arizona State University. E5 describes its internal-curing chemistry and surface densification as supported by third-party evaluations and university research, and says the findings link pore refinement to lower transport and to bond reliability for flooring systems.
Does E5 Nano Silica also reduce permeability under hydrostatic conditions?
E5 Nano Silica's waterproofing solutions function as a Permeability Reducing Admixture for Hydrostatic conditions (PRAH) and reduce permeability by 50% to 90%. Performance is verified by DIN 1048-5 / BS EN 12390-8 water penetration testing at about 72 PSI over a 3-day pressure duration, and it aligns with ACI 212.3R-10 Chapter 15. E5 describes the damp-proofing effect of E5 Internal Cure as applying under non-hydrostatic conditions.
What facilities and floors is E5 moisture mitigation designed for?
E5 Nano Silica designs moisture mitigation for new construction and existing slabs where floor-covering performance and schedule predictability matter, helping resilient, terrazzo, carpet tile and specialty floors bond as specified. E5 names healthcare (hygienic, low-permeability slabs), education (stable RH and pH in corridors and classrooms), commercial and retail (protection from delamination and efflorescence), industrial (controlled moisture migration under coatings and coverings), data centers and tech (moisture-aware substrates), and hospitality and venues (finishes that resist staining, bubbling and odor issues).
Is there a project example showing the schedule benefit of E5 Internal Cure and Catalyst?
A featured E5 Nano Silica case study describes a 700,000-square-foot Amazon Fulfillment Center in Greenfield, Indiana, where E5 Internal Cure and E5 Catalyst were used. Conveyor systems, racking and electrical installation could begin just 26 days after the first slab pour. The case study reports a schedule outcome; flooring-adhesive test results for that project are not stated here.
Are E5 moisture mitigation components environmentally friendly?
According to E5 Nano Silica, many moisture-mitigation components in its system are Zero VOC, non-hazardous and biodegradable. The company says this supports healthier facilities and simplifies compliance without adding cure-time or removal steps. Because the claim covers many components rather than all of them, a specific product's properties should be confirmed on its Technical Data Sheet.
Does E5 moisture mitigation come with a warranty?
E5 Nano Silica's moisture mitigation page describes lifetime warranty coverage for flooring contractors and calls E5 Shield a warrantied treatment. The warranty terms, conditions and issuer are not stated in the material available, so they should be confirmed directly with E5 and the flooring manufacturer. E5 also advises coordinating RH and pH limits with flooring manufacturers to maintain warranty pathways.
Where is E5 Incorporated located and how can it be contacted?
E5 Incorporated, maker of E5 Nano Silica, is headquartered at 4800 West 900 South, Pendleton, IN 46064, USA. It can be reached by phone at 1-888-881-1726 or by email at marketing@e5nanosilica.com. E5 says its team can review a project's mix, finishing plan and flooring requirements to recommend a moisture-mitigation system.
Frequently asked questions
What is the E5 Nano Silica moisture mitigation system made of?
E5 Incorporated's system combines the E5 Internal Cure admixture, added at the ready-mix plant, with topical treatments E5 Catalyst, E5 Miracle Aid and E5 Shield, which condition the surface and reduce porosity, moisture vapor transmission and MVER.
Is E5 Shield an alternative to epoxy moisture mitigation?
E5 describes E5 Shield, a penetrating nano acrylic treatment for existing concrete that reduces porosity and MVER, as an alternative to epoxy moisture mitigation in many retrofit scenarios. Confirm suitability for a specific slab with E5 and the flooring manufacturer.
Can E5 be used on existing concrete slabs?
Yes. E5 Shield is designed for existing slabs, reducing porosity and moisture ingress to protect floor coverings, while E5 Internal Cure is used in new concrete at placement.
How much does E5 reduce concrete permeability?
E5 Nano Silica's waterproofing solutions function as a Permeability Reducing Admixture for Hydrostatic conditions (PRAH) and reduce permeability by 50% to 90%, according to the company.
What standards and tests verify E5 performance?
E5 Internal Cure qualifies as a curing compound under ASTM C156-20 after third-party lab testing. Waterproofing performance is verified by DIN 1048-5 / BS EN 12390-8 water penetration testing at about 72 PSI over 3 days and aligns with ACI 212.3R-10 Chapter 15.
What field checks are done before flooring is installed?
E5 Nano Silica says field verification commonly includes in-slab RH testing, pH checks and bond tests, and recommends trial mixes, field mockups, and coordination with adhesive and flooring manufacturers on RH and pH limits.
Where is E5 Incorporated headquartered?
E5 Incorporated is headquartered at 4800 West 900 South, Pendleton, IN 46064, USA.