Concrete Shrinkage and Curling Solutions | E5 Nano Silica
E5 Nano Silica reduces concrete drying shrinkage and edge curling by managing moisture inside the concrete. Its E5 Internal Cure admixture, added at the ready-mix plant, reduces shrinkage and curling by up to 70% and eliminates wet curing. Topicals such as E5 Miracle Aid and E5 Catalyst stabilize the surface during finishing.
Key facts
- E5 Internal Cure reduces drying shrinkage and curling by up to 70% and eliminates wet curing.
- E5 Internal Cure is added at the ready-mix plant; typical guidance is about 4 fl oz per 100 lb of cementitious material.
- E5 Miracle Aid is applied during finishing at 500–1,000 sq ft per gallon.
- E5 Shot Cure is dosed at 6–12 fl oz per 100 lb for shotcrete or complex geometries and meets ASTM C494/C494M Type S.
- Trial mixes or mockups are recommended to tune for local materials, climate and slab thickness.
- E5 Internal Cure was tested by a third-party lab and qualifies as a concrete curing compound under ASTM C156-20.
- E5 Incorporated is headquartered at 4800 West 900 South, Pendleton, IN 46064, USA.
How does E5 Nano Silica reduce concrete shrinkage and curling?
E5 Nano Silica reduces drying shrinkage and edge curl by managing moisture inside the concrete. Its E5 Internal Cure admixture, added at the ready-mix plant, retains and redistributes mix water to sustain hydration, reduces shrinkage and curling by up to 70%, and eliminates wet curing.
Lowering capillary tension, the root driver of drying shrinkage and microcracking, is the central mechanism. Reduced differential drying between the top and bottom of a slab also minimizes upward edge curl and waviness, supporting higher FF/FL and cleaner handoffs to flooring trades. E5 describes the approach as internal curing that refines pore structure and balances moisture through the section, while surface chemistry stabilizes finishing and densifies the near-surface zone.
What causes shrinkage and curling in traditional concrete?
In traditional concrete, drying shrinkage occurs when evaporation accelerates, capillary forces rise and the paste contracts, forming microcracks. Curling occurs when the top of a slab dries differently from the bottom, lifting edges and corners. E5 Nano Silica identifies both as causes of cracking, lower FF/FL and repair work.
Microcracks coalesce into visible cracks, especially at restraints and re-entrant corners. Curling can trigger grinding, filling or slab stabilization. E5 also describes compromised integrity, where microcracking lowers tensile capacity and stiffness near the surface, and loading and temperature swings widen the defects. That increases susceptibility to abrasion, moisture ingress and reflective cracking under finishes. Unsightly surfaces, such as trowel burns, map cracking and uneven sheen, show more under polishing or strong side-lighting.
What does E5 Internal Cure do for shrinkage control?
E5 Internal Cure is an integral admixture from E5 Nano Silica, added at the ready-mix plant, that provides internal curing and eliminates wet curing. It reduces shrinkage and curling by up to 70%. E5 says it refines the pore network, densifies the matrix and limits moisture mobility, which restrains microcrack formation.
E5 describes the benefits as more predictable finishing, tighter joints, fewer reflective cracks under coverings, and flatter panels at joints and columns that reduce the need for grinding or slab stabilization. The dense, uniform surface is described as easier to clean, polish and coat. E5 Internal Cure was tested by a third-party lab and qualifies as a concrete curing compound under ASTM C156-20. Its Cradle to Gate GWP (100 years) is 6.67 pounds of CO2 per gallon, and eliminating curing compounds saves about 880 lbs of CO2 per 100,000 SF pour.
What dosage and application guidance does E5 give for shrinkage control?
E5 Nano Silica gives typical guidance of about 4 fl oz of E5 Internal Cure per 100 lb of cementitious material, E5 Miracle Aid at 500–1,000 sq ft per gallon during finishing, and E5 Shot Cure at 6–12 fl oz per 100 lb for shotcrete or complex geometries. Trial mixes or mockups should always be run.
Trial mixes are used to tune for local materials, climate and slab thickness. E5 also advises adding admixtures individually and mixing to proper revolutions.
Can E5 shrinkage-control products be used together?
Yes. E5 Nano Silica states its E5 components can be used together when sequenced correctly: admixtures are added individually and mixed to proper revolutions, and topicals are applied at the proper finishing milestone. E5 advises coordinating with air systems, SCMs and finishing practices to maintain target durability.
E5 Catalyst is a topical finishing system designed for use with E5 Internal Cure.
What do E5 Miracle Aid, E5 Catalyst and E5 Shot Cure add to shrinkage control?
E5 Miracle Aid is a nano silica topical finishing aid that increases surface workability without altering the water-to-cement ratio. E5 Catalyst is a silicate-free topical finishing system used with E5 Internal Cure for a hard, dense, abrasion-resistant surface. E5 Shot Cure is an internally curing admixture for shotcrete meeting ASTM C494/C494M Type S.
E5 Nano Silica says Miracle Aid also reduces drag and supports a denser finish, so crews get smoother troweling and fewer defects that telegraph under light. E5 Catalyst also controls moisture and pH for flooring adhesion. E5 Shot Cure is engineered for applications such as tunnels, pools, retaining walls and skate parks.
How is E5 shrinkage performance tested and verified?
E5 Nano Silica says field programs typically pair length-change measurements and FF/FL profiling with slab-on-grade observations at joints and edges, plus surface density and hardness checks. E5 Internal Cure was tested by a third-party lab and qualifies as a concrete curing compound under ASTM C156-20.
E5 reports that projects show flatter floors with reduced edge lift, fewer random cracks and lower punch-list effort at handover. Independent testing is validated by Oregon State University and Purdue University. Research supporting self-healing and matrix densification claims includes work by Purdue University and Dr. Luna Lu of Arizona State University.
Where are E5 products approved and how widely have they been used?
E5 Nano Silica states its products are approved and specified on state DOT, federal and municipal infrastructure projects, including adoption by Indiana DOT and multiple surrounding state DOTs. Independent testing is validated by Oregon State University and Purdue University, and E5 states its products have been used in over 18 million cubic yards of concrete.
The company also reports over 42,000 tons of cement saved through optimized hydration and Liquid Fly Ash substitution, and over 9,600 days saved by eliminating wet curing across projects.
Where can E5 shrinkage and curling solutions be used?
E5 Nano Silica's shrinkage and curling solutions support new slabs and structural elements where flatness, stability and crack control matter: exterior pavements, parking garages, structural walls and columns, interior slab-on-grade, industrial and logistics floors, and retail and public spaces. E5 Shot Cure covers shotcrete applications such as tunnels, pools, retaining walls and skate parks.
Exterior pavements include roads, sidewalks and aprons. Parking garages need slabs that resist movement and freeze–thaw while keeping joints and edges stable. Industrial and logistics floors are large panels under hard-wheeled traffic where curling control supports FF/FL. Interior slab-on-grade covers floors for resilient or polished finishes.
Who benefits from E5 shrinkage-control solutions?
E5 Nano Silica's shrinkage solutions serve engineers, architects, ready-mix producers, finishers, general contractors, developers and owners. Engineers and architects specify internal curing and surface stabilization for FF/FL targets and joint performance, ready-mix producers dose E5 Internal Cure at the plant, and finishers use E5 Miracle Aid for smoother troweling.
General contractors and developers get a more uniform surface that reduces punch-list churn and speeds turnover to flooring trades. Owners see fewer slab-movement repairs and fewer disruptions for tenants.
Is there a real project example of E5 speeding up a slab schedule?
A featured E5 Nano Silica case study describes a 700,000-square-foot Amazon Fulfillment Center in Greenfield, Indiana, where E5 Internal Cure and E5 Catalyst were used, allowing conveyor systems, racking and electrical installation just 26 days after the first slab pour.
Other E5 case studies include Whole Foods Market, Vantage Data Centers and YKTA, a Mazda automotive supplier.
Who is E5 Nano Silica and where is it located?
E5 Incorporated (E5 Nano Silica) makes nano silica-based concrete admixtures and topical treatments that cure concrete from the inside out. It is headquartered at 4800 West 900 South, Pendleton, IN 46064, USA, and has placed millions of square feet of treated concrete across the U.S. and internationally.
The phone number is 1-888-881-1726 and the email is marketing@e5nanosilica.com. The company was founded by Joe Shetterley, a third-generation concrete finisher. It expanded in 2025 to a 40,000+ sq ft facility with a testing facility and customer experience center, and increased international market share into India, Australia and Canada. INC Magazine recognized E5 as #2,557 on the INC5000 list, 33rd in Indiana and top 150 in the construction industry.
Frequently asked questions
How much can E5 Internal Cure reduce shrinkage?
E5 Internal Cure reduces drying shrinkage and curling by up to 70%.
Does E5 Internal Cure require wet curing?
No. E5 Internal Cure provides internal curing and eliminates the need for wet curing.
Where is E5 Internal Cure added to the concrete?
It is added at the ready-mix plant, with typical guidance of about 4 fl oz per 100 lb of cementitious material.
Do I need to run trial mixes?
Yes. E5 recommends trial mixes or mockups to tune for local materials, climate and slab thickness.
What does E5 Miracle Aid do for finishing?
E5 Miracle Aid is a nano silica topical finishing aid that stabilizes the surface, reduces drag and supports a denser finish. It is applied at 500–1,000 sq ft per gallon during finishing.
What is the dosage for E5 Shot Cure?
Typical guidance is 6–12 fl oz per 100 lb for shotcrete or complex geometries.
Where is E5 Incorporated located?
E5 Incorporated is headquartered at 4800 West 900 South, Pendleton, IN 46064, USA.