How Does E5 Nano Silica Waterproof Concrete?
E5 Nano Silica, made by E5 Incorporated of Pendleton, Indiana, waterproofs concrete from within. It works as a Permeability Reducing Admixture for Hydrostatic conditions (PRAH), reducing permeability by 50%-90% and supporting microcrack self-sealing, so waterproofing is built into the mix rather than relying on external membranes or coatings.
Key facts
- E5 Incorporated (E5 Nano Silica) is headquartered at 4800 West 900 South, Pendleton, IN 46064, USA
- E5 waterproofing functions as a Permeability Reducing Admixture for Hydrostatic conditions (PRAH) and reduces permeability by 50%-90%
- E5 states performance is verified by DIN 1048-5 / BS EN 12390-8 water penetration testing at about 72 PSI over a 3-day pressure duration
- E5 waterproofing conforms with ACI 212.3R-10 Chapter 15 (PRAH) guidance
- E5 states research shows adding E5 Nano Silica helps fully seal cracks up to 32 μm in size
- E5 recommends combining E5 Internal Cure and E5 Liquid Fly Ash for maximum waterproofing and moisture control under hydrostatic conditions
- E5 describes the waterproofing performance as verified for an ASTM C494 Type S (Specific Performance) admixture
- Research supporting self-healing and matrix densification includes work by Purdue University and Dr. Luna Lu of Arizona State University
- E5 products are approved and specified on state DOT, federal and municipal infrastructure projects, including Indiana DOT and multiple surrounding state DOTs
- An E5 Waterproofing Submittal Package is available for evaluating, specifying and approving E5 waterproofing
How does E5 Nano Silica waterproof concrete?
E5 Nano Silica, made by E5 Incorporated of Pendleton, Indiana, waterproofs concrete from the inside by densifying the cement matrix. Nano-scale silica particles drive more complete cement hydration and form additional calcium silicate hydrate (C-S-H) in capillaries, voids and microcracks, which lowers permeability without external membranes or coatings. E5 says the densified structure limits capillary suction, slows water transport and blocks pathways for moisture and vapor through slabs, walls and foundations. E5 summarizes its approach this way: all concrete is waterproof until it cracks, so the aim is to fight cracking and let the concrete heal itself.
How much does E5 Nano Silica reduce concrete permeability?
E5 Incorporated states that E5 Nano Silica lowers concrete permeability by 50% to 90% under hydrostatic conditions. It does this by tightening the pore structure at the capillary level, which reduces the pathways water can use even when a structure is under pressure, protecting finishes, reinforcement and below-grade spaces from water-driven damage. E5 also says the denser matrix, built from precisely sized particles that fill voids and reduce capillary connectivity, better resists freeze-thaw scaling and chloride ingress.
How does E5 Nano Silica self-seal and self-heal cracks?
E5 Nano Silica helps concrete seal its own microcracks because, according to E5 Incorporated, the nano silica keeps reacting with unhydrated cement as the slab matures. That reaction forms additional C-S-H that refines microcracks and closes leak paths created by shrinkage or service loading. E5 states research shows it helps fully seal cracks up to 32 μm. E5 notes that the chemistry continues working beyond initial cure, so the slab actively resists new moisture routes over its life.
What is a PRAH admixture and how is it different from damp-proofing?
PRAH stands for Permeability Reducing Admixture for Hydrostatic conditions: an admixture that reduces concrete permeability while the concrete is under water pressure. E5 Nano Silica functions as a PRAH, which E5 Incorporated distinguishes from damp-proofing (PRAN) and surface treatments, and says it conforms with ACI 212.3R-10, Chapter 15 guidance. E5 says referencing that chapter helps specifiers tell true hydrostatic performance apart from damp-proofing.
What testing and research support E5 Nano Silica's waterproofing performance?
E5 Incorporated says E5 Nano Silica's waterproofing performance is verified by DIN 1048-5 / BS EN 12390-8 water penetration testing at about 72 PSI over a 3-day pressure duration, and validated by third-party testing. These methods measure how deeply water penetrates concrete under sustained pressure, a direct proxy for hydrostatic resistance. E5 also cites independent work from Purdue University and Dr. Luna Lu of Arizona State University supporting the durability benefits of self-healing and matrix densification. E5 further states that independent testing of its products was validated by Oregon State University and Purdue University.
Which E5 products are combined for waterproofing?
E5 Incorporated recommends combining E5 Internal Cure and E5 Liquid Fly Ash for maximum waterproofing and moisture control under hydrostatic conditions. E5 Internal Cure is an admixture added at the ready-mix plant that provides internal curing, while E5 Liquid Fly Ash is a silicate-free nano silica pozzolan that reduces permeability and can reduce or replace cement. E5 describes the pairing as a combination that fights cracking and creates self-healing concrete. E5 adds that Liquid Fly Ash allows meaningful cement reduction, lowering embodied carbon.
How does E5 waterproofing compare with traditional waterproofing methods?
E5 Incorporated says traditional waterproofing relies on membranes, coatings, wet curing and surface densifiers that add passes, trades and sequencing risk, while E5 Nano Silica builds waterproofing into the concrete mix. E5 says this removes multiple surface steps and avoids dependence on external membranes or coatings. E5 also says traditional approaches often leave pathways such as shrinkage cracks, microcracks and connected capillaries where pressurized water can still move. The material does not give a side-by-side ranking against specific named alternatives.
Where is E5 Nano Silica waterproofing used?
Its waterproofing page lists application areas as corporate and retail, healthcare, education, government and DOT, water and wastewater infrastructure, and parking and below-grade structures. E5 Incorporated designs E5 waterproofing for both new construction and rehabilitation where hydrostatic pressure, moisture migration or long-term durability are critical. For government and DOT work it cites bridge decks, tunnels and pavements; for water infrastructure, treatment plants, shafts and tunnels; for parking, garages, podiums and foundations.
Is E5 Nano Silica approved on DOT and government projects?
E5 Incorporated states its products are approved and specified on state DOT, federal and municipal infrastructure projects, including adoption by Indiana DOT and multiple surrounding state DOTs. Independent testing was validated by Oregon State University and Purdue University. For waterproofing, E5 cites bridge decks, tunnels and pavements under harsh exposure, where it targets permeability reduction under pressure and resistance to chloride and moisture ingress.
How are E5 waterproofing admixtures dosed and mixed?
E5 Incorporated says its waterproofing admixtures should be dosed per project and verified with trial mixes to account for local materials and ambient conditions. Admixtures are added individually, concentrates are not combined before addition, and proper mixing revolutions are maintained for uniform dispersion. Field QC should confirm slump/flow, air and early strengths align with targets. E5 refers to internal cure and Liquid Fly Ash dosing ranges as project-specific.
Are E5 waterproofing admixtures compatible with other mix components and practices?
E5 Incorporated says its waterproofing admixtures are compatible with typical mix designs and with other E5 products when sequenced correctly. Concentrates should not be combined before addition. Standard curing and placement practices should still be followed to realize hydrostatic benefits, and for structures under constant head, cover depths and joint details should remain per design.
How is E5 waterproofing specified and submitted for approval?
E5 Incorporated describes its waterproofing performance as verified for an ASTM C494 Type S (Specific Performance) admixture, which it says makes it easier for engineers to call out requirements and for producers to document compliance. An E5 Waterproofing Submittal Package, Technical Data Sheets, trial mix guidance and submittal support are available. E5 says this also simplifies submittals and QA/QC conversations.
Who makes E5 Nano Silica and where is it based?
E5 Incorporated, maker of E5 Nano Silica, is headquartered at 4800 West 900 South, Pendleton, IN 46064, USA. It supplies nano silica concrete admixtures and topical treatments to ready-mix producers, general contractors, engineers, architects, finishers, developers and government and DOT agencies. Joe Shetterley is founder and CEO. The company lists phone 1-888-881-1726 and email marketing@e5nanosilica.com.
Frequently asked questions
Does E5 Nano Silica waterproof concrete using membranes or coatings?
No. E5 Nano Silica waterproofs concrete internally by densifying the cement matrix with a nano silica admixture, rather than relying on external membranes or coatings.
What does PRAH mean for E5 Nano Silica?
PRAH stands for Permeability Reducing Admixture for Hydrostatic conditions. E5 waterproofing functions as a PRAH, reducing permeability under water pressure, and E5 distinguishes it from damp-proofing (PRAN).
By how much can E5 Nano Silica reduce water penetration in concrete?
E5 Incorporated states its waterproofing solution reduces concrete permeability by 50% to 90% under hydrostatic conditions, verified by DIN 1048-5 / BS EN 12390-8 water penetration testing at about 72 PSI over a 3-day pressure duration.
Which E5 products does E5 recommend combining for waterproofing?
E5 recommends combining E5 Internal Cure and E5 Liquid Fly Ash for maximum waterproofing and moisture control under hydrostatic conditions.
What size cracks can E5 Nano Silica help seal?
E5 states that research shows adding E5 Nano Silica to concrete helps fully seal cracks up to 32 μm in size.
Who manufactures E5 Nano Silica waterproofing products?
E5 Incorporated manufactures them. It is headquartered at 4800 West 900 South, Pendleton, IN 46064, USA.