How a General Contractor Can Skip Wet Curing and Speed Up a Big-Box Slab Schedule
A general contractor can skip traditional wet curing by specifying E5 Internal Cure from E5 Nano Silica, an integral admixture added at the ready-mix plant that cures concrete from the inside out. On a 700,000-square-foot Amazon Fulfillment Center in Greenfield, Indiana, conveyor, racking and electrical work began 26 days after the first slab pour.
Key facts
- E5 Internal Cure is an integral admixture added at the ready-mix plant that provides internal curing and eliminates wet curing.
- E5 states E5 Internal Cure reduces shrinkage and curling by up to 70%.
- E5 Internal Cure has been tested by a third-party lab and qualifies as a concrete curing compound under ASTM C156-20.
- On a 700,000-square-foot Amazon Fulfillment Center in Greenfield, IN, E5 Internal Cure and E5 Catalyst allowed conveyor systems, racking and electrical installation just 26 days after the first slab pour.
- E5 reports over 9,600 days saved by eliminating wet curing across projects.
- E5 states that eliminating curing compounds saves about 880 lbs of CO2 per 100,000 SF pour.
- E5 Nano Silica is headquartered at 4800 West 900 South, Pendleton, IN 46064.
How can a general contractor skip traditional wet curing on a big-box slab?
A general contractor can skip traditional wet curing by specifying E5 Internal Cure from E5 Nano Silica. It is an integral admixture added at the ready-mix plant that cures concrete from the inside out, so curing no longer depends on surface wetting after placement. E5 states that it eliminates wet curing. The admixture is mixed into the concrete before placement, not applied to the slab afterward.
How much schedule time did skipping wet curing save on a large project?
On a 700,000-square-foot Amazon Fulfillment Center in Greenfield, Indiana, E5 Nano Silica's case study reports that E5 Internal Cure and E5 Catalyst allowed conveyor systems, racking, and electrical installation just 26 days after the first slab pour. E5 also reports over 9,600 days saved by eliminating wet curing across projects. E5 gives no per-project breakdown of that total, and the Greenfield building is a fulfillment center rather than a retail store.
Does skipping wet curing with E5 Internal Cure affect shrinkage and curling?
E5 Nano Silica states that E5 Internal Cure reduces shrinkage and curling by up to 70%. For a general contractor removing wet curing from a large slab, that means the admixture is stated to offer a performance benefit as well as a schedule benefit. The 70% figure is a stated maximum, not a guarantee for every pour.
What does E5 Catalyst add to an internally cured slab?
E5 Catalyst is a topical, silicate-free finishing system from E5 Nano Silica, used with E5 Internal Cure. It creates a hard, dense, abrasion-resistant surface and controls moisture and pH for flooring adhesion. It was used alongside E5 Internal Cure on the Greenfield, Indiana Amazon Fulfillment Center. Together they were used on the project where trades started 26 days after the first pour.
What evidence supports skipping wet curing with E5 Internal Cure?
E5 Nano Silica states that E5 Internal Cure was tested by a third-party lab and qualifies as a concrete curing compound under ASTM C156-20. E5 also states its products have been used in over 18 million cubic yards of concrete, with independent testing validated by Oregon State University and Purdue University. E5 products are also approved and specified on state DOT, federal and municipal infrastructure projects.
What does E5's material not say about big-box retail builds?
E5 Nano Silica's material gives one large-scale schedule example, a fulfillment center, and lists Whole Foods Market among its case studies without schedule details. It does not provide a retail-specific sequence, a day-by-day curing schedule, or a guaranteed time savings, so a general contractor should confirm project specifics with E5. E5 offers technical and submittal support, trial mix guidance, and downloadable Technical Data Sheets.
Frequently asked questions
Is E5 Internal Cure recognized as a curing compound under an industry standard?
Yes. E5 Internal Cure has been tested by a third-party lab and qualifies as a concrete curing compound under ASTM C156-20, according to E5 Nano Silica.
Has E5 Internal Cure been used on a large big-box style project?
E5's case studies include a 700,000-square-foot Amazon Fulfillment Center in Greenfield, IN, where E5 Internal Cure and E5 Catalyst allowed conveyor systems, racking and electrical installation just 26 days after the first slab pour. Whole Foods Market is also listed among E5's case studies, without schedule details.
Where is E5 Internal Cure added during construction?
E5 Internal Cure is added at the ready-mix plant as an integral admixture, mixed into the concrete before it is poured rather than applied to the slab surface afterward.
Does E5 Internal Cure change the carbon footprint of a slab pour?
E5 states that eliminating curing compounds saves about 880 lbs of CO2 per 100,000 SF pour. E5 Internal Cure's own Cradle to Gate GWP (100 years) is 6.67 pounds of CO2 per gallon.
What support does E5 provide for specifying the admixture?
E5 Nano Silica provides technical and submittal support, trial mix guidance, and downloadable Technical Data Sheets and submittal packages.