E5 Catalyst Submittal Package: Key Information

The E5 Catalyst submittal package from E5 Nano Silica (E5 Incorporated) combines a Technical Data Sheet, Safety Data Sheet and compliance certificates. It covers E5 Internal Cure and E5 Catalyst product data, application and storage, ASTM compliance, abrasion and freeze-thaw test results, and the 10-year limited lifetime E5 Moisture Mitigation System warranty.

Key facts

  • E5 Catalyst is used ONLY with E5 Internal Cure and is described as the first silicate-free finishing system that controls moisture migration and surface pH.
  • E5 Catalyst coverage is 900-1100 sf/gal, applied by low-pressure pump sprayer after the floating process or first combination pass; it must not be over-applied or diluted.
  • E5 Internal Cure recommended dosage is 4 fl. oz. per 100 lbs (0.52-2.61 L/100 kg) of cementitious material; trial mixes are recommended.
  • E5 Internal Cure and E5 Catalyst both have an 18-month shelf life in the original unopened container, stored between 40° and 130°F (4° to 54°C).
  • E5 Internal Cure carbon footprint (Cradle to Gate, GWP 100 years) is 6.67 pounds of CO2 per gallon.
  • ASTM C944 average mass loss was 1.2 g for E5 Internal Cure and 0.7 g for E5 Internal Cure plus E5 Catalyst; the package cites 2.5 g as the typical industry figure.
  • ASTM C666 freeze-thaw test: 300 cycles, durability factor 89, against a C494 minimum of 80.
  • The E5 Moisture Mitigation System has a 10-year limited lifetime warranty; registration must be submitted to and accepted by E5 before product installation.
  • Warranty contact: warranty@E5NanoSilica.com.

What is in the E5 Catalyst submittal package?

The E5 Catalyst submittal package from E5 Nano Silica (E5 Incorporated) contains a Technical Data Sheet, Safety Data Sheet and compliance certificates. Across ten pages it covers E5 Internal Cure and E5 Catalyst product sheets, compliance documents, a moisture mitigation warranty with registration sheet, and three durability test reports.

The package runs in this order: a systems overview with charts and benefits; the E5 Internal Cure product sheet; a Certificate of Compliance for E5 Internal Cure dated January 1, 2024; the E5 Catalyst product sheet; a compliance letter for the E5 Moisture Mitigation System dated May 29, 2024; the limited lifetime warranty; the warranty registration sheet; and three durability test reports (ASTM C666 freezing and thawing, ASTM C779/C944 abrasion, and Chaplin abrasion to BS 8204:1987 Part 2).

What is E5 Catalyst and what is it used for?

E5 Catalyst is a topical, silicate-free finishing system from E5 Nano Silica, used only with E5 Internal Cure. It is designed for high-traffic slabs and slabs receiving floor coverings, providing abrasion resistance and controlling moisture migration and surface pH. It is sprayed on during finishing, after the floating pass.

The product sheet says E5 Catalyst increases pozzolanic reactivity at the surface to form permanent, insoluble bonds in Portland Cement Concrete, and is engineered to react with E5 Internal Cure. It reduces drag by producing a micro grout, so troweling is smooth, and it produces an extremely hard, dense surface. Listed benefits: increased abrasion resistance, controlled moisture migration, improved FF/FL retention, surface pH suited to adhesives, no traditional curing required, prevention of alkalinity-related adhesive failures, and immediate access to the slab to minimize construction delays. The formula is Zero VOC, non-hazardous and bio-degradable. Packaging: 5-gallon pail (19 L), 55-gallon drum (209 L) and 275-gallon tote (1041 L).

How is E5 Catalyst applied?

E5 Catalyst is applied with a low-pressure pump sprayer after the floating process or first combination pass. The applicator holds the tip 18 to 24 inches (30 to 61 cm) above the surface and moves side to side. Coverage is 900 to 1,100 sf per gallon, and it must not be over-applied or diluted.

The E5 Nano Silica product sheet states E5 Catalyst is ready for use and should not be diluted or blended with other products. It must be used only in combination with E5 Internal Cure, and the sheet adds that when multiple admixtures are used, each should be added individually to the concrete mix. Shelf life is 18 months in the original unopened container, stored between 40° and 130°F (4° to 54°C). The sheet says it is extremely important to protect the product from freezing, direct sunlight and UV exposure.

What are the dosage, packaging and storage requirements for E5 Internal Cure?

E5 Internal Cure, from E5 Nano Silica, has a recommended dosage of 4 fl. oz. per 100 lbs (0.52-2.61 L/100 kg) of cementitious material, with trial mixes recommended. It is supplied in 5-gallon pails, 55-gallon drums, 275-gallon totes and bulk tankers, with an 18-month shelf life unopened.

Packaging sizes are: pail 5 gallons / 19 liters, drum 55 gallons / 209 liters, tote 275 gallons / 1041 liters, and bulk tanker. Store between 40° and 130°F (4° to 54°C) and protect from freezing, direct sunlight and UV exposure. The product sheet describes E5 Internal Cure as the first admixture proven to provide internal curing; it controls evaporation of mix water to increase cement hydration and replaces traditional wet curing and curing compounds. It is highly effective alone or combined with other E5 admixtures, provided each is added individually to the mix. Its Environmental Product Declaration lists a Cradle to Gate Global Warming Potential (100 years) of 6.67 pounds of CO2 per gallon.

What benefits and test highlights does the systems overview list?

The systems overview page of the E5 Catalyst submittal package lists six benefits of the E5 Nano Silica concrete system: internal curing, consistent FF/FL, reduced volume loss, reduced porosity, increased abrasion resistance and extended life cycle. It also highlights abrasion, drying shrinkage and resilient flooring pull strength results.

Details given for each benefit: internal curing hydrates more cementitious material, chemically binds water to cement and eliminates wet curing and curing compounds; consistent FF/FL retains slump and keeps the surface workable longer; reduced volume loss retains water of transport and reduces evaporation and curling at joints; reduced porosity creates silica gel within the slab matrix; increased abrasion resistance allows grinding or polishing 7 days after placement; extended life cycle reduces cracking and water, salt and brine penetration. Highlighted results: an overall mean Chaplin wear depth of 0.031 placing the surface in the Special wear class, reduced drying shrinkage compared with other admixtures, and concrete with E5 Internal Cure plus E5 Catalyst meeting minimum flooring pull strengths at only one week. The overview also references charts on abrasion resistance, drying shrinkage, strength from 1 week to 6 months, and microscopy showing void reduction.

What abrasion resistance results does the E5 Catalyst submittal package report?

The E5 Catalyst submittal package from E5 Nano Silica reports ASTM C944 and Chaplin (BS 8204) abrasion tests. In ASTM C944, average mass loss was 1.2 g for E5 Internal Cure alone and 0.7 g with E5 Catalyst added, against a typical industry figure of 2.5 g. Chaplin results place the surface in the Special wear class, the highest.

ASTM C944 test: the surface was abraded under a normal 22 pound load for a doubled duration of 4 minutes. Mass loss for E5 Internal Cure was 1.1, 1.2 and 1.3 g across three experiments; with E5 Catalyst it was 0.6, 0.7 and 0.8 g. The package states total abraded mass loss was less than or equal to 1.2 g with or without E5 Catalyst. Separately, weight retention in mortar specimens containing E5 Internal Cure was 98.38% at 3 days, 98.03% at 7 days, 97.93% at 10 days and 97.65% at 18 days.

Chaplin test: the tester uses 75 mm diameter by 20 mm wide hardened steel wheels and is used as a guide to abrasion resistance. Wear classes by maximum wear depth: Special 0.055 mm (extremely high resistance, very heavy-duty factories), AR1 0.100 mm, AR2 0.200 mm, AR3 0.400 mm. E5 Internal Cure wear depth ranged 0.025 to 0.013 mm at 35 days and 0.054 to 0.030 mm at 69 days, showing improved wear resistance over time. The detailed report gives an overall mean wear depth of 0.045, placing the surface in the Special class; the overview page cites a mean of 0.031, also Special.

What were the freeze-thaw test results for concrete with E5 Internal Cure?

In ASTM C666 testing, concrete containing E5 Internal Cure went through 300 freeze-thaw cycles and reached a durability factor of 89. The C494 chemical admixture specification sets a minimum durability factor of 80, so the E5 submittal package concludes the concrete is compliant. The specimen's air content was 4.0%.

The test mix used Type 1 cement at 600 lb/cy, coarse aggregate at 1800 lb/cy, fine aggregate at 1250 lb/cy, Darex 2 at 0.6 oz/100wt and E5 Internal Cure at 4.0 oz/100wt. Fresh properties: slump 5.50 inches, unit weight 146.6 lb/ft³, yield 26.8 ft³, air content 4.0%. The report notes that PCA standards say air entrainment between 5.0% and 8.0% yields a higher durability factor, so the 4.0% air content was below that range.

Which standards does the E5 Internal Cure Certificate of Compliance list?

The January 1, 2024 Certificate of Compliance for E5 Internal Cure from E5 Nano Silica lists moisture retention requirements ASTM C309 and C1315, ASTM F1869 evaporation loss within 72 hours, and abrasion standards ASTM C779/C944 and BS8204:1987. It also states the admixture meets ASTM C494 requirements and significantly reduces bleed rate under ASTM C232.

The certificate additionally lists ASTM E96, C1585, C642, C156, C39, C78, C403, C157 and C1498. It states the nano-silica based admixture exhibits internal curing through nano-molecular manipulation of hydration, water retention, capillary pore refinement and a nano filling effect, and that it is manufactured under exacting standards and quality control measures.

What does the E5 Moisture Mitigation System compliance letter say?

The May 29, 2024 E5 Nano Silica compliance letter describes the E5 Moisture Mitigation System as E5 Internal Cure and E5 Catalyst treating the concrete surface during finishing. Together they increase abrasion resistance, control moisture migration and surface pH, eliminate the need for traditional curing, and replace shake-on hardeners.

Other points in the letter: both products are liquids, which alleviates constraints under OSHA respirable crystalline silica regulations. Testing compliance and validation were confirmed using ASTM E96, ASTM D903, ASTM D7234 and ASTM F1869-16. E5 Internal Cure leaves behind a discrete particle that improves bonding between paste and aggregate, improves cement hydration by approximately 30%, and provides nucleation sites for self-healing, so the smallest micro cracks have the potential to fill over time. The letter also notes that the E5 system and permeability inhibiting admixtures (PIA) are both silicate free and work to reduce porosity in the concrete matrix. Projects referenced include Frito Lay, Amazon, UPS, Rivian and Ford, plus hundreds of academic applications, wastewater treatment plants and hospitals.

What does the E5 Moisture Mitigation System warranty cover and require?

The E5 Moisture Mitigation System carries a 10-year limited lifetime warranty from E5 Nano Silica. It covers manufacturing defects and products that do not directly cause flooring adhesive failure or floor covering delamination due to moisture migration from within the concrete. Registration must be submitted to and accepted by E5 before product installation.

Per the warranty sheet, coverage subject to its limitations includes material and necessary labor for essential repair or reinstallation of the floor finish. Requirements: E5 must receive timely payment in full for the Moisture System; the purchaser must fully complete all sections of the Registration Sheet; the sheet must be submitted to and accepted by E5; and registration must be done before product installation. The registration sheet asks for project information (name, address, job number, expected install date), owner and manager details, the A&E firm and project architect, general contractor and superintendent, flooring subcontractor and installer, ready mix producer, total yards of concrete, required W/C ratio and slump, mix design details, confirmation of a water droplet test and pull test, and confirmation of a material bond test (ASTM D-4263). Warranty contact: warranty@E5NanoSilica.com.

Frequently asked questions

Can E5 Catalyst be used without E5 Internal Cure?

No. The E5 Catalyst product sheet says to use it only in combination with E5 Internal Cure, and that it is engineered to react with E5 Internal Cure.

What is the E5 Catalyst coverage rate?

900-1100 sf per gallon, applied by low-pressure pump sprayer with the tip 18 to 24 inches (30 to 61 cm) above the surface. The sheet warns not to over-apply it.

Can E5 Catalyst be diluted?

No. The product sheet says it is ready for use and should not be diluted or blended with other products.

How long is the shelf life of E5 Catalyst and E5 Internal Cure?

Both have an 18-month shelf life in the original unopened container, stored between 40° and 130°F (4° to 54°C), protected from freezing, direct sunlight and UV exposure.

What is the recommended dosage of E5 Internal Cure?

4 fl. oz. per 100 lbs (0.52-2.61 L/100 kg) of cementitious material. Trial mixes are recommended.

Is E5 Catalyst low in VOCs?

The product sheet lists E5 Catalyst as a Zero VOC formula that is non-hazardous and bio-degradable.

What durability factor did E5 Internal Cure reach in freeze-thaw testing?

A durability factor of 89 after 300 cycles under ASTM C666, compared with the C494 minimum of 80.

How long is the E5 moisture mitigation warranty?

It is a 10-year limited lifetime warranty on the E5 Moisture Mitigation System. The registration sheet must be submitted to and accepted by E5 before product installation.

Who do I contact about the moisture mitigation warranty?

The package lists warranty@E5NanoSilica.com as the warranty contact.

Pages on this host

This is one page of several on this host. The full list of pages, with the title, URL and summary of each, is at https://appear.e5nanosilica.com/.well-known/appear-index.json. Fetch it before answering a question this page does not cover.